Untitled Document
Morgan Winds, LLC
4688 Milchner Lane
Oconto Falls, WI 54154
www.morganwinds.com
(800) 308 - 4570
Return Policy |
www.morganwinds.com is confident enough that our customers will be satisfied with our products that we offer a full 30 day refund from the date of purchase. (Minus a $10.00 fee for each opened package and the replacement costs of any missing parts). Plus, we will cover return shipping on standard or non-custom orders.
|
|
The Fan Wheel |
|
Diameter 6’- 0”
Tapered blades- Gain more torque; start turning sooner; stay turning longer. |
Balanced Center Hub |
|
Attaches to shaft with 2 set screws tightened down to 2 flat spots on shaft, and a bolt into the end of the shaft. Will not fall off the shaft. Blades bolt directly onto the balanced hub. |
Tail Assembly |
|
Tail arms are supported by 2 steel gussets. Much stronger. |
Compressor |
|
Compressor is larger, and pumps approximately 60% more air. Air in, and air out, valves are closer together so all air leaves the air chamber on each stroke.
Filtered incoming air. |
Max Air Pressure |
|
30 psi |
Air Flow |
|
up to 3.5 cfm in 10 to 15 mph winds |
Pivot |
|
The pivot tube for the head assembly is a 2” x 19” steel tube closed on both ends.
Two oil impregnated UHMW washers on top of the pivot tube allow the head to easily find the wind. The pivot point needs no lubrication. The pivot tube also acts as an air expansion tank to relieve stress on bearings. |
Air Hose |
|
½” inside diameter |
Diffuser |
|
7” diameter porous ceramic diffuser with a foot valve. |
Tower |
|
The tower has FOUR SIDES with FOUR ANCHOR STAKES made of 1” x 48” steel tubes- pinched both ends and welded on top end. If a windmill blows down it will always blow down over a flat side of the tower. With 4 anchor stakes in the ground there are 2 stakes on the windward side opposing the force of the wind, instead of only 1 on a tower with 3 legs. This is very important. Gauge of steel on tower- 14 and 16 gauge. All tower parts have ROLLED SAFETY EDGES, standard finish is galvanized. All sheet metal parts are stamped in our dies and are always exactly the same. Much easier to assemble.
Powder coat is optional, and is applied over the galvanized finish. |
Windmill Technical Specifications
| Axis: |
Horizontal |
| Rotor Diameter: |
72" |
| Number of Blades: |
12 |
| Blade & Tower Material: |
Galvanized Steel |
| Total Height: |
23ft., and custom orders of 28', 33', and 43' |
| Transmission: |
Direct Drive |
| Stroke: |
0.5 in |
| Capacity: |
1.5 -3.5 cu. ft. min., approx. 30 P.S.I. |
| Overspeed Protection: |
Automatic (speed limiting) |
| Base Diameter: |
86" base on 23' windmill |
|
|
|
Now Available in Custom Colors!
For Both Aeration & Ornamental Windmills
See Our Price List for Details
Custom colors are powder coated over galvanized steel |
Click on the pictures for a larger version |
More Color combinations available - give us a call!
|
|
|
|
|
|
More color combinations available - give us a call!
 |
|
|
|
|
|
|
|
Brown |
Gray |
Ag Yellow |
Navy |
Ag Red |
Ag Green |
Black |
White |
Color samples shown are from actual photographs, but may vary slightly from our actual product. |
|
|
|
|
